feed hole
英 [fiːd həʊl]
美 [fiːd hoʊl]
网络 输送孔; 馈送孔; 传动导孔
双语例句
- Repeat steps ( 3) through ( 6) to wrap the blue loose end around the yellow loop, feed through the hole and pull tight to complete the second stage.
重复步骤（3）通过（6）包装的蓝松年底左右的黄色环，通过饲料和拉孔紧，完成第二阶段。 - Start to feed the left lace into the "hole" that has just been made.
开始喂左边花边的“洞”了刚才的讲话。 - Grip the enlarged handle of the hook and feed the wire loop through the button hole.
抓住钩的扩大柄和通过按键洞喂电报圈。 - Advanced feed hole: Refer to sprocket holes of paper tape, which are in line with the leading edge of the code holes.
前向齿孔：纸带上和代码孔相并行排列的齿轮孔。 - With the cooperative control of drawing temperature and feed speed, the final hole structure can be effectively controlled by tuning the applied pressure.
在温度和送料速度的协调控制下，通过调节气压参数可有效控制气孔结构。 - Feed electrical wires of new switch assembly through hole in rear of housing.
从壳后将新的开关总成的火线穿过壳上的孔。 - Sorry it took so long, but someone tried to feed us to a black hole.
不要意思花了这么长时间，不过有人想用我们去喂白洞。 - Feed the right ( yellow) loop back through the "hole" for the second time.
饲料权（黄色）环回通过的“洞”的第二次。 - The Impact of Feed Rate on the Vibration Drilling Dispersity of the Hole Diameter
进给量对振动钻削孔径分散度的影响 - Relying mainly on expanding in static behavior on later stage to cram and feed through holes through the liquid phase material, adjust and optimize the structure of hole, we successfully improved the strength and reduced the hole rate.
后期以静态膨胀为主，通过液相物质填堵连通孔，调整优化孔结构，提高强度，降低孔隙率。 - In this article, establishing the mathematical model for optimal feed path during machining hole system with same profile characteristics on machining centers or point-to-point positioning NC machine tools and the solution of this model are expounded.
本文阐述了加工中心及点位数控机床上加工相同形面特征孔系时，刀具最佳走刀路线顺序确定数学模型的建立以及解决该模型的算法。 - The rice seedling are vertically feed accurately without relative slip error, and the seedling separating accuracy is ensured by using a grid plate rubber conveying belt with the equidistance hole on both sides.
该机构采用等距型孔栅板橡胶带实现纵向进给，无相对滑差，进给准确，确保栽植机构准确分秧。 - The results showed that the whole pellet feed produced by higher conditioning temperature, smaller diameter of die hole was of benefit to improving performance of broilers.
结果表明，采用高调质温度、小孔环模生产的不破碎颗粒料，有利于改善肉鸡的上述2个生产性能指标。 - PLC controls the two stepping motors to drive workpieces double feed, an idles old common lathe is refit into a special equipment to process end face and center hole by using numerical controlled technique.
同时，采用PLC控制两台步进电机驱动工件实现自动进给，使其成为一台适用于轴类零件中心孔和端面加工的专用机床。